Tech Feature: Garage Files Upgrading Your Fork Seals To SKF

Screen Shot 2015-10-08 at 9.09.45 AM

One of the unsung heroes of the modern mountain bike is the lowly fork wiper. It’s a small part, but it makes a huge difference in the way your suspension feels, and it needs to be replaced more frequently than you might expect. Time and time again we encounter riders who have run their forks into the ground by not changing wipers or the lubricating bath oil that keeps a fork running smoothly.

Fork seals have to function in a very demanding environment, and while fork manufacturers have worked hard to improve their own seal systems, SKF has developed a range of aftermarket seals tuned to reduce friction, improve suspension feel and increase the life of the fork. SKF seals are said to be better at sealing out water and dirt, which keeps lubrication oil cleaner over the life of the seal. We put a set of these seals through the wrecking crew wringer, but first we had to install them.

This procedure is for a Fox 36 RC2 fork, although it’s very similar to the installation procedure for most major brands. If it’s been a season or more since your last suspension service, whether or not you choose to upgrade to an aftermarket seal like the SKF, it’s time to show your bike some love. We’ll show you how.

1-Start by removing the fork from the bike. While it is possible to do this operation without this step, it’s much easier this way.

2-If you have a bike repair stand, clamp the fork’s steerer tube in the stand.

3-Remove the air cap (if applicable) and release all the air pressure from the fork.

Garage-44-Remove the protective cap from the rebound knob.

Garage-4b5-Use a 2-millimeter Allen wrench to loosen the set screw on the rebound knob and remove the knob.

 Garage-56-Use a 15-millimeter wrench to remove the foot nut from the right fork leg.

   Garage-5b7-Use a 10-millimeter wrench to remove the foot nut from the left- side leg.

Garage-78-Use a socket over the rebound knob to protect the delicate rebound adjuster knob. Then use a hammer to tap the rod free from the lowers of the fork.

Garage-89-If you’ve done this right, there should be some oil that pours out of the fork leg. Use an oil-catch pan to keep your garage floor clean.

Garage-910-Now, tap the left side in a similar fashion to break it free from the fork legs. More oil will pour out of this side too.

Garage-1011-With both rods free, you will be able to remove the lowers from the fork.

12-Clean the damper rods and upper tubes with a clean paper towel.

Garage-1213-For good measure, wipe any excess dust from the seals, being careful not to spread dirt into the lowers.

Garage-1314-Use an open-ended wrench as a lever to remove the dust wipers from the fork.

Garage-1415-Once the dust wipers are removed, remove the foam rings.

Garage-1516-Thoroughly clean the lowers with isopropyl alcohol and a clean paper towel.

Garage-1617-Get your SKF seal kit ready.

18-Using 20-weight Fox suspension oil, thoroughly lubricate the new foam rings.

19-Find an appropriately sized seal press. This 36-millimeter fork works well with a standard bottom bracket tool. An appropriately sized tool will fit nicely over the springs and only press on the outer rim of the seal.

Garage-1920-Lightly lubricate the lower half of the new seal.

Garage-2021-Install the soaked foam rings.

Garage-2122-Use the seal press to evenly press in the new seals. This should be fairly easy to do and should not need more pressure than with your hand.

Garage-2223-Ensure that the seal is fully installed and bottomed out on the lowers.

24-Replace the lowers on the upper tubes.

25-It’s easy to pinch the foam rings in this process. If there’s any resistance, it’s better to pull off the lowers and start again.

26-Invert the fork in the bike stand.

27-Pour fresh oil into a syringe. For the right side, this fork requires 30cc, and the left side requires 10cc. This level will vary between manufacturers and models, so check the company website for the exact fork oil levels.

28-Use the tip of the syringe to pour the oil into the bottom of the fork legs.

29-Place the plastic crush washers included in the seal kit on the corresponding fork-leg rods.

Garage-3130-Be sure to use a pick to pull out the old crush washers from the foot nuts.

31-Use the open-ended wrenches to tighten the foot nuts.

32-It’s easy to over-tighten these foot nuts, and it’s best to use a torque wrench, although many will forgo this step.

33-Replace the rebound knob on the right side and re-tighten the 2-millimeter set screw. Be sure to align the bolt with the groove on the rebound rod before tightening.

34-Replace the protective cap.

35-Re-pressurize the air spring.

36-Enjoy your buttery-smooth new seals!


Mountain Bike Action is a monthly magazine devoted to all things mountain biking (yes, that’s 12 times a year because we never take a month off of mountain biking). It has been around since 1986 and we’re still having fun. Start a subscription by clicking here or calling (800) 767-0345. Available from the Apple Newsstand for reading on your iPad, iPhone or iPod Touch.

Contact us via email at


Comments are closed.